Loading...

Power 12 Power Distribution Center:

The Power 12 Power Distribution Center provides Ignition Hot, and Timed Hot outputs in banks of 6 fused outputs. The control cards, DC-IGN and DC-TMD, regulate the Ignition Hot and Timed Hot Circuits. Either Control Card may be replaced to provide 12 Ignition Hot, 6 Ignition & 6 Timed, or 12 Timed Hot Outputs. The Power 12 should be fed by a 6 Gauge Power and Ground Cable fused at 125 Amps.

Low Voltage Disconnect – In order to ensure that a temporary load does not create a nuisance shut-down the P12  Timer will wait 15 seconds before disconnecting the circuit.

Over-Voltage Protection – Immediately disconnects the circuit when voltage exceeds 18 VDC. Reconnects when voltage returns to <18 VDC.

Infinite Mode – Setting the timer to Infinite Mode allows computers and radios to stand by for immediate response. The infinite mode also supports VPN communications through onboard routers, allowing the operator to securely communicate with the IT network even when the vehicle is off. The DVT timer will only disconnect when the voltage falls below the low voltage setting and the system will reset once the voltage recovers to 11.9 VDC.

Solid State Design – Eliminates heat build-up and voltage drop across the device.

Ignition Override – When time is critical the ignition override ensures operation of communications equipment.

Specifications P12-i4T2T6:

• Length: 10”
• Width: 5.57”
• Height: 1.25”
• Weight: 2.04lb
• Max Load: 125A total combined output
• 2 Separate Timer or ignition cards
• Timer One: 4 Ignition Outputs, 2 Timed Outputs, 30A max.
• Timer Two: 6 Timed Outputs, 30A max.
• 32 Timed intervals
• 2 Diagnostic LEDs per Timer, 4 total

Dual Voltage Timer: supports Police, Fire, and
Utility truck applications.
• 11.0 VDC: The “Off ” position equals a low
voltage disconnect of 11.0 VDC.
• 11.75 VDC: The “On” position equals a low
voltage disconnect of 11.75 VDC.

Low Voltage Disconnect:
The low voltage limit is controlled by a dip
switch.
• The Low Voltage Disconnect only occurs
when the ignition is off .
• Override: If the ignition is turned on, the
timed outputs become active.
High Voltage Disconnect:
18.0 VDC: The High Voltage Disconnect occurs
whenever the voltage is greater then 18.0 VDC.
• Override: None
• If a high or low voltage event occurs the
Voltage Status LED will fl ash in RED for 3
ignition cycles.

Details

Power 12 Power Distribution Center:

The Power 12 Power Distribution Center provides Ignition Hot, and Timed Hot outputs in banks of 6 fused outputs. The control cards, DC-IGN and DC-TMD, regulate the Ignition Hot and Timed Hot Circuits. Either Control Card may be replaced to provide 12 Ignition Hot, 6 Ignition & 6 Timed, or 12 Timed Hot Outputs. The Power 12 should be fed by a 6 Gauge Power and Ground Cable fused at 125 Amps.

Low Voltage Disconnect – In order to ensure that a temporary load does not create a nuisance shut-down the P12  Timer will wait 15 seconds before disconnecting the circuit.

Over-Voltage Protection – Immediately disconnects the circuit when voltage exceeds 18 VDC. Reconnects when voltage returns to <18 VDC.

Infinite Mode – Setting the timer to Infinite Mode allows computers and radios to stand by for immediate response. The infinite mode also supports VPN communications through onboard routers, allowing the operator to securely communicate with the IT network even when the vehicle is off. The DVT timer will only disconnect when the voltage falls below the low voltage setting and the system will reset once the voltage recovers to 11.9 VDC.

Solid State Design – Eliminates heat build-up and voltage drop across the device.

Ignition Override – When time is critical the ignition override ensures operation of communications equipment.

Data Sheet

Specifications P12-i4T2T6:

• Length: 10”
• Width: 5.57”
• Height: 1.25”
• Weight: 2.04lb
• Max Load: 125A total combined output
• 2 Separate Timer or ignition cards
• Timer One: 4 Ignition Outputs, 2 Timed Outputs, 30A max.
• Timer Two: 6 Timed Outputs, 30A max.
• 32 Timed intervals
• 2 Diagnostic LEDs per Timer, 4 total

Dual Voltage Timer: supports Police, Fire, and
Utility truck applications.
• 11.0 VDC: The “Off ” position equals a low
voltage disconnect of 11.0 VDC.
• 11.75 VDC: The “On” position equals a low
voltage disconnect of 11.75 VDC.

Low Voltage Disconnect:
The low voltage limit is controlled by a dip
switch.
• The Low Voltage Disconnect only occurs
when the ignition is off .
• Override: If the ignition is turned on, the
timed outputs become active.
High Voltage Disconnect:
18.0 VDC: The High Voltage Disconnect occurs
whenever the voltage is greater then 18.0 VDC.
• Override: None
• If a high or low voltage event occurs the
Voltage Status LED will fl ash in RED for 3
ignition cycles.

Data Sheet
Layout

P12-i4T2T6

$650.84

NEW PRODUCT

The Power 12 Power Distribution Center provides Ignition Hot, and Timed Hot outputs in banks of 6 fused outputs. (30A Max ea.) with a 125Amp max output.